Wood Venetians 50/63mm

MATERIALS & SIZES

Basswood, available in 50mm and 63mm slats.

STANDARD OPERATING SYSTEM

Cord operation including cord lock

LIMITATIONS

• Maximum width is 2410mm
• Maximum drop is 3200mm
• Minimum width is 300mm
• Minimum drop is 200mm
• Single blind size should not exceed 6m2
• Over 6m2 will be made as 2-ON-1 head-rail,  max width of 3010mm and max drop is 3200mm

HEAD-RAIL TYPES 

• 53mm x 58mm High Profile Steel Head-rail
• 2-ON-1 head-rail

ACORN & BREAKAWAY CORD JOINER

Material : PVC
Metal acorn in antique brass and gold

MINIMUM RECESS DEPTH (REVEAL)

• Fully recessed 65mm no return required
• Semi recessed – as requested. Note : minimum return is 20mm

FACE FIT

• Standard returns are 70mm
• Add extra for architrave depth if returning to the wall

CORD LENGTHS – (unless otherwise specified)

• Standard factory calculation is 2/3 rds of the drop of the blind in the down position
• Child Safety Breakaway is located approx 100mm from the cordlock in the down position
• Tilt cord minimum length is 550mm

VALANCES

• 50mm – 75mm Flat Valance
• For 2-ON-1 head-rail over 2410mm, the valance will have a miter joint. Male to male velcro is supplied to attach the valance to the head-rail.
• Valance size based on head-rail size after deductions
  – Standard valance return length is 70mm
  – Reveal Fit extra 9mm
  – Face Fit extra 20mm
  Reveal Fit – no return ends
  Face Fit – returns to be nominated (eg right only, left only, left & right)

2-ON-1 BLIND OPERATION

For tilt and lift options, cords cannot be placed in the center of the blinds. Cords can be both left, both right, left/right, and right/left

HOW TO CALCULATE A DROP MEASUREMENT

Our standard drop measurement is achieved when the blind is in the closed position with the bottom-rail tilted. When the blind is in the open position, the lowest point of the bottom-rail will sit around 10mm higher than when the blind is in the closed position. If using hold down clips, the bottom-rail will sit around 10mm above the reveal in the closed position and in the open position around 20mm above (50mm slat) & 30mm above (63mm slat).

STANDARD TOLERANCE

Please note that our standard tolerance for blind width and blind drop is +-5mm. if the blind is made within our tolerance range, no claim will be accepted.

WARRANTY INFORMATION

Component : 3 years
Colour : 2 years

COLOUR VARIATION

Due to the use of natural materials, colour variation will sometimes occur with Timber Venetians.

CLEANING / REGULAR CARE

Use a soft duster or non-coloured cleaning cloth. Wipe gently with a damp cloth to remove dust or marks from the blind surface using a chemical-free or mild detergent. Do not rub or use any abrasive substances or solvent.

LARGER SIZES

As a general rule, Econowood blinds over 3m2 are heavy and can be difficult to lift. Depending on the application, it is advised to use two or more blinds on one head-rail. When lifting larger blinds, the operator should guide the blind by holding the base-rail as they are lifting it up. Due to memory retention, blinds should not be left in the up position for any extended length of time. If the blind warps as a result of this no claim will be accepted.

LIGHT BLEED

All blinds allow light to pass through around the sides of the blind. In addition, there will be small pin holes of light in each slat where the ladder cords pass through. Consider using face fit as an option rather than reveal fit to reduce light bleed at the sides. This is not a blockout blind.

CUTOUTS

A cutout is a blind with an area removed from it to avoid an existing obstruction. Please provide detailed measurements of the area to be removed. Maximum Depth of Cut Out is 100mm per side. Surcharges apply, please refer to “Surcharge & Option” list.